[VTA] cma settings for de10 nano

Questions
#1

Hello.

I am trying to run VTA on DE10 Nano. And there is a problem using cma to allocate memory during the tutorial - at running test_benchmark_topi_conv2d.py.

It would help me a lot if you could answer some questions:

  1. Can someone please respond who launched TVM with VTA on de10nano - which version of TVM did you use?
  2. Where did you get the cma allocator?
  3. De10nano has 1GB DDR memory, how much memory do we need to allocate for cma?

Thanks in advance!

#2

I ran into the same problem. I tried to enable CMA by compiling Linux kernel but I couldn’t get it.

I tried this instruction and I enabled CMA in the kernel config. Then I booted with the kernel but /dev/cma doesn’t exist.

Environment:

OS: Angstrom Linux (downloaded from Terasic’s website)

#3

Hello, check do you have /dev/-cma

image

Also you could check cma module installed:

$ lsmod | grep cma

cma 16384 0

To check available volume of cma:

$ cat /proc/meminfo

image
image310×609 11.4 KB

#4

Thank you for helping me.

I don’t see /dev/-cma. Also I don’t see cma in module.

But I see CmaTotal and CmaTree in /proc/meminfo.

# ls /dev/
autofs           gpiochip0         mmcblk0             ptyp0  ptypc   tty0   tty2   tty30  tty41  tty52  tty63  ttyp6    vcs1   vcsa6
block            gpiochip1         mmcblk0p1           ptyp1  ptypd   tty1   tty20  tty31  tty42  tty53  tty7   ttyp7    vcs2   watchdog
btrfs-control    gpiochip2         mmcblk0p2           ptyp2  ptype   tty10  tty21  tty32  tty43  tty54  tty8   ttyp8    vcs3   watchdog0
bus              i2c-0             mmcblk0p3           ptyp3  ptypf   tty11  tty22  tty33  tty44  tty55  tty9   ttyp9    vcs4   zero
char             i2c-1             mqueue              ptyp4  ram0    tty12  tty23  tty34  tty45  tty56  ttyS0  ttypa    vcs5
console          initctl           network_latency     ptyp5  ram1    tty13  tty24  tty35  tty46  tty57  ttyS1  ttypb    vcs6
cpu_dma_latency  input             network_throughput  ptyp6  random  tty14  tty25  tty36  tty47  tty58  ttyp0  ttypc    vcsa
cuse             kmem              null                ptyp7  shm     tty15  tty26  tty37  tty48  tty59  ttyp1  ttypd    vcsa1
disk             kmsg              psaux               ptyp8  stderr  tty16  tty27  tty38  tty49  tty6   ttyp2  ttype    vcsa2
fd               log               ptmx                ptyp9  stdin   tty17  tty28  tty39  tty5   tty60  ttyp3  ttypf    vcsa3
full             mem               ptp0                ptypa  stdout  tty18  tty29  tty4   tty50  tty61  ttyp4  urandom  vcsa4
fuse             memory_bandwidth  pts                 ptypb  tty     tty19  tty3   tty40  tty51  tty62  ttyp5  vcs      vcsa5

# lsmod
Module                  Size  Used by
xt_connmark            16384  2
iptable_nat            16384  0
nf_conntrack_ipv4      16384  3
nf_defrag_ipv4         16384  1 nf_conntrack_ipv4
nf_nat_ipv4            16384  1 iptable_nat
nf_nat                 28672  1 nf_nat_ipv4
nf_conntrack          122880  4 nf_conntrack_ipv4,xt_connmark,nf_nat_ipv4,nf_nat
iptable_mangle         16384  1
iptable_filter         16384  0
ip_tables              20480  3 iptable_mangle,iptable_filter,iptable_nat
x_tables               28672  4 iptable_mangle,ip_tables,iptable_filter,xt_connmark

# cat /proc/meminfo | grep Cma
CmaTotal:          16384 kB
CmaFree:           16100 kB
#5

Hello Masahiro,

this is the way how I did:

for add cma kernel module, take zImage and cma.ko from here GitHub - liangfu/de10-nano-supplement

copy this zImage to /mnt/boot/ on your de10nano

make a copy of your /mnt/boot/devicetree…… .dts, e.g. “test.dts”

add new section to this test.dts and build test.dtb, then copy test.dtb to /mnt/boot

reserved-memory { #address-cells = <1>; #size-cells = <1>; ranges;

    default_cma_pool: default_cma_pool {
        compatible = "shared-dma-pool";
        reusable;
        size = <0x18000000>;
        alignment = <0x10000>;
        linux,cma-default;
    };
};

reboot with new zImage

$ sudo reboot

select uBoot from the menu

=> setenv linux_kernel_image zImage; setenv linux_fdt_image test.dtb; run bootcmd

install cma module

$ sudo insmod cma.ko

check that cma module was installed with lsmod command and check memory with cat /proc/meminfo

#7

I successfully enabled cma. But I sticked into the cma memory allocation error when I tried to run VTA’s getting started tutorial.

# ./apps/vta_rpc/start_rpc_server.sh
INFO:RPCServer:bind to 0.0.0.0:9091
INFO:RPCServer:connection from ('192.168.10.101', 54884)
INFO:root:Skip reconfig_runtime due to same config.
INFO:root:Loading VTA library: /home/root/workspace/tvm/vta/python/vta/../../../build/libvta.so
INFO:RPCServer:load_module /tmp/tmplz7m5ivo/vadd.o
CMA_API_DEBUG: Opening "/dev/cma" file
CMA_API_DEBUG: Allocating 0x200 bytes of contigous memory
CMA_API_DEBUG: Getting physical address from 0xb2911000
CMA_API_DEBUG: Allocating 0x200 bytes of contigous memory
CMA_API_DEBUG: Getting physical address from 0xb28fc000
CMA_API_DEBUG: Allocating 0x80 bytes of contigous memory
CMA_API_DEBUG: Getting physical address from 0xb253d000
CMA_API_DEBUG: Allocating 0x2000000 bytes of contigous memory
CMA_API_DEBUG: Getting physical address from 0xb053d000
CMA_API_DEBUG: Allocating 0x2000000 bytes of contigous memory
CMA_API_DEBUG: Getting physical address from 0xae53d000
CMA_API_DEBUG: Releasing contigous memory from 0xb2911000
CMA_API_DEBUG: Releasing contigous memory from 0xb28fc000
CMA_API_DEBUG: Releasing contigous memory from 0xb253d000
CMA_API_DEBUG: Releasing contigous memory from 0xae53d000
CMA_API_DEBUG: Releasing contigous memory from 0xb053d000
CMA_API_DEBUG: cma_free - ioctl command unsuccsessful - 0
INFO:RPCServer:Finish serving ('192.168.10.101', 54884)
#8

I’m facing the same issue, did you finally solved it? The cma memory doesn’t free in any of the tvm-vta examples except for the deploy_classification.py example